85040系列拉压力传感器

耐用,非常精确,长久耐用,适用于静态和动态力,侧向力灵敏度极低,防护等级高,不锈钢

  • Features

    • 量程范围从 0 ... 20 N 到 0 ... 2 MN
    • 适合静态和动态测试
    • 测量精度≥ 0.1 % F.S.
    • 不容易受到侧向力影响
    • 型号85073/85075适用于高频动态测试,85070系列可承受1亿次测试循环
    • 可扩展温度补偿范围从-55°C...+120°C(选配)
    • 保护等级IP 68 (选配)
  • Product data

    型号 85041,85043, 85073,85075
    量程范围 85041 0 … 20 N
    0 … 50 N
    0 … 100 N
    0 … 200 N
    0 … 500 N
    0 … 1 kN
    0 … 2 kN
    0 … 5 kN
    0 … 10 kN
    0 … 20 kN
    0 … 50 kN
    0 … 100 kN
    0 … 200 kN
    0 … 500 kN
    0 … 1 MN
    0 … 2 MN 85043 0 … 20 N
    0 … 50 N
    0 … 100 N
    0 … 200 N
    0 … 500 N
    0 … 1 kN
    0 … 2 kN
    0 … 5 kN
    0 … 10 kN
    0 … 20 kN
    0 … 50 kN
    0 … 100 kN
    0 … 200 kN
    0 … 500 kN
    0 … 1 MN
    0 … 1,5 MN
    0 … 2 MN 85073 0 … 200 N
    0 … 500 N
    0 … 1 kN
    0 … 2 kN
    0 … 5 kN
    0 … 10 kN
    0 … 20 kN
    0 … 50 kN
    0 … 100 kN
    0 … 200 kN
    0 … 500 kN
    0 … 1000 kN 85075 0 … 200 N
    0 … 500 N
    0 … 1 kN
    0 … 2 kN
    0 … 5 kN
    0 … 10 kN
    0 … 20 kN
    0 … 50 kN
    0 … 100 kN
    0 … 200 kN
    0 … 500 kN
    受力方向 85041 & 85075
    拉力和压力

    85043 & 85073
    压力
    标准化信号 No
    信号输出 2 mV/V
    3 mV/V
    取决于量程大小
    保护等级 IP64 (可选配 IP68)
    过载保护 No
    拉盘 85041 & 85075
    Yes

    85043 & 85073
    No
    受力压头 No
    使用温度范围 -55 ... +120 °C
    具体特点 85041 & 85043 适合一般静态和动态测试


    85073 & 85075

    合适极高频率的高动态测试
    • Description

      These load cells feature an outstanding ability to withstand static and dynamic stress and have exceptional precision and service life. These products have a huge range of applications in industry, R+D and testing thanks to the optional IP68 degree of protection and low sensitivity to lateral forces.

      Examples of applications would be the measurement of:

          Insertion forces
          Reference measurement
          Weights (e.g. silos, skips)
          Tensile forces (tension in cables, chains etc. with load centering plate)
          Materials testing

      For the compressive force sensors (models 85043 and 85073) the force must be applied through a plane plate, hard enough for the range of forces being measured, or a piston.

      The force-sensitive diaphragm with fitted strain gauges is located between the central part, where the force is applied (force application), and the outer ring (containing fixing holes).

      Two support diaphragms are additionally fitted, above and below the actual measuring element, to desensitize the sensors to extraneous lateral forces or moments. (see „Permitted external forces“ on page 2).

      Models 85041/85075 (tension/compression) are calibrated in the tensile direction. The characteristic figure for the compression direction can nominally vary by ± 0.25 % from the figure for the tensile direction. The output signal is positive when the applied force is tensile.

      The 8507X series (models 85073 and 85075) is designed for the highest possible dynamic stress and service life. This is > 109 cycles from zero up to the full value of the measuring range in the tensile or compressive direction and tolerates a maximum operational force of up to 200 % of the nominal range.

    • Downloads

      Data sheet
      pdf 85040系列参数资料
    • Accessories

      pdf Rod ends with internal/external thread for force introduction

    Related products

    Product comparison

      © 2020 波司特精密仪器(上海)有限公司 沪ICP备12015704号沪公网安备31010602000957号